17 Reasons To Not Ignore Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain, durable and long-lasting. They are not susceptible to decay or rust as timber and aluminum.

It is essential to clean and oil UPVC windows and doors regularly. This will help prevent unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows could cause significant damage to your home and even be fatal. It is important to ensure that your windows are in good working order.

For single pane windows it can be relatively simple to replace them, and the replacement will usually fit inside the frame that was previously installed easily. However when you have double pane windows that are secured by internal beading it will be more difficult to get rid of the existing panes and install new ones. In this instance, it is necessary to buy plastic spacers to help the new pane fit into the window frame.

If you're planning to attempt to remove the glass panes yourself it is crucial to wear the proper safety gear, including thick gloves and eye protection. It is also a good idea to lay down a drop cloth before you start working on the glass, so that any shards will fall onto the cloth rather than on the floor where they can be trodden under and cause further damage.

After the glass has been removed and the glass is removed, it's a good idea to cover the gap with clear packaging tape or duct tape to stop water and drafts from getting into the home until a professional comes out and fix the window. It also acts as a barrier, deterring any intruders to gain access into your home. If the gap is large, you might want to consider using the security door with an integrated window as it will provide the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable, durable and energy-efficient alternative to timber sash windows. Over time, they can develop a variety of issues, including sagging. A window that isn't properly aligned can cause problems with light, draughts or even security. If you notice that your uPVC window is beginning to shrink, it's important to act quickly to stop the issue from worsening.

To repair a window that is sagging, you can try to reposition the hinges. First, you'll need to open the windows to get at the frame. Then, you can remove the hinges on the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Close your window to test the fit after you have repositioned your hinges. If you're satisfied with the fit of your window, you can tighten screws to hold them in place.

If you are unable to reposition the hinges, you might need to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, causing them to loose their elasticity. If this happens, it's crucial to replace the seal as quickly as possible so that your uPVC windows remain watertight and safe from drafts.

UPVC handles can also become loose. This is typically caused by screws that have loosened over time, but it can be due to the handle mechanism getting worn out. Luckily, it's not difficult to fix a loose uPVC window handle yourself. The first step is to close the window and perform an experiment to ensure that it fits. The joint at the corners of the sash should align with the joint on the casing. If it does not, you can use the screwdriver to loosen the handle. Then turn the mechanism back into place.

3. Water Leaks

It is crucial to take action if get up each morning to discover mouldy walls and floors that are wet. Water leaks through windows can cause structural damage to your home and also impact your ability to regulate the temperature inside your home. The most common cause for leaking uPVC windows is that the sealant around the frame has been damaged or is missing.

This is a fairly simple fix that can be done by any skilled DIYer. Based on the severity of the issue the caulking used previously may need to be removed before a new layer of caulk can be applied. When it is time to uPVC repair, you should avoid 'over-caulking'. This will make your window harder to clean and reduce its energy efficiency.

Make sure that the drainage holes have no debris in them, and also ensure that the sill pan has been properly angled to drain away from the window. In more severe instances, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the home.

If the leakage occurs between the double-glazed window, it is more likely the issue is more related to the seal, not the frame. A uPVC specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or if it opens in a breeze. Any competent DIYer can replace these in a matter of minutes.

Almost every household in the UK will have top-hung or side-hung uPVC windows that use hinges and like any mechanical part they can wear down over time. It's easy to replace a hinge on a window, but it's easier if someone helps you to hold the frame.

It is also worth checking that the uPVC hinges are opening and closed in the correct direction. This can be done by looking for the arrow on each hinge. This indicates the direction in which the window should be opened.

The issue can be caused either due to opening the window in the wrong way or by a poor installation at the factory. Sending us a photo via our website will often resolve the problem. We are always happy to offer assistance.

Regularly lubricating hinges is also essential. Applying a light engineering lubricant on the hinges is a great method to accomplish this. We suggest using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window repair easier to open and close. It can also lower the possibility of a window sticking and prevent corrosion. It is recommended to perform this every year. WD40 and other solvent-based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a few different things. The hinges can also be unbalanced due to wear, creating gaps where the sash and frame meet. These can be easily fixed by giving them a thorough clean, UPVC Window Repair however when they're beyond repair, it might be necessary to get them aligned or replaced. The interlock may also become disaligned. This happens on the hinge side and could require to be cleaned. In some instances it is possible to replace them.

These seals can wear down or become damaged over time, allowing air escape. Replacing these with high-quality weatherstripping will help to keep draughts at bay. Replace the windows made of upvc with low-emissivity glasses. This will help regulate indoor UPVC Window Repair temperatures, and reduce the risk of draughts.

The final method to cut down on drafts effectively is to use a Draught-excluder. These are usually fabric tubes filled with a filler which can be hung over your window sill. They can help stop cold air from entering and keep your home warm and cozy!

With a little maintenance and repairs windows made of Upvc window repair will continue to provide an excellent level of insulation and security for your home. It is crucial to realize that all windows have a lifespan and they may reach the point when it's more cost-effective to replace them rather than repair them. So, if you are experiencing problems with your upvc windows, it's recommended to seek help from a professional immediately.