Five Kia Picanto Key Fob Replacement Lessons From The Pros

How to Replace a Kia Sportage Replacement Key

For many Kia models the key comes with the keyless entry system that is built into the key. This key is similar to an remote control, and is exchangeable by an Kia dealer.

Key fobs are prone to malfunction for several reasons, including the battery of the coin is dead worn buttons or buttons, water damage, signal interference and a damaged receiver module. Here are some helpful tips on how to get your Kia Sportage replacement key back to working.

How do you replace the remote key or smart key?

It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start key, or a standard non-transponder key made of metal The battery inside these keys will eventually require replacement. This is especially the case if your car displays a message that indicates the smart or remote keys are in poor condition.

This is a relatively easy procedure. To replace the battery of the key fob, remove the mechanical key from the slit on the back of the key fob. Next, remove the cover. Inside the key fob will be tiny screws that hold the battery in the correct position. Take out the old battery by unscrewing the screw using a small screwdriver. Then, insert the new and close the hole in the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors lock and unlock according to your expectations, then you're all set! You can now utilize the Kia's hands-free lock/unlock feature whenever your fingers feel cold or you have to run some errands in Brandon.

Not all keys may require to be programmed (transponder chips or smart keys). This requires a machine for programming, which is only available to the locksmith in the automotive or dealer. Other keys (non-transponder metal keys) do not require programming. If you're required to reprogramme your key, you'll need record the key code number on the key code tag.

How do I replace the battery?

If the Kia key fob doesn't respond to pressing the lock/unlock button, it is likely that the battery is insufficient. A low battery may also cause other issues, such as the check engine light flashing on or the engine not cranking. It is fairly easy to replace key fob batteries using just a few simple tools.

Make sure that you shut off your vehicle and shut all doors before you begin. Locate the small metal or plastic piece that is on the bottom of your key fob, and jiggle it until a metal key is released. You can then insert the key in the door handle of the driver to open your car.

To replace the key fob battery, take off the cover from the back and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery and then orient the new one to ensure that the "+" positive side faces you and the "-" negative side is facing the fob's electronic contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

Once the new battery is installed and the key fob is turned on, turn it off and back on in the ignition repeatedly until the door locks cycle. Then, you can test your kia picanto key fob replacement key fob to check whether it's working again.

How do you replace a smart key

There is a possibility of having a standard keyfob, or a Smart Key based on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade while the standard keyfob does not. Both key fobs have a battery that will eventually require changing. Fortunately, it's an easy task that only takes about two minutes.

Be sure to turn off your kia sportage key fob and stand on a level or well-lit surface prior to when you begin. Be aware that there are tiny parts inside the fob that can fall out if you are not vigilant.

The first step is to locate the small release button on the back of the lower part of the fob. It could be a circular or rectangular slot. Once you press this, the mechanical key blade will appear and you can then open the key fob.

After the key fob has been removed, you can remove the battery that was in it. The new battery is a C2032, and can be purchased online or in your local auto parts shop. After installation it should be possible to lock or unlock your vehicle with your key fob even if your engine isn't running!

How do you replace a mechanical key

The Kia keyfob can be a fantastic convenience which allows us to lock or unlock our car by pressing the button. However, like all devices, it can have problems at times. There are steps to take to solve these issues and ensure that our key fobs are in good condition in the long run.

One of the most common problems is a low or dead battery. This can cause the device to stop working completely or to work intermittently. If this happens, try replacing the battery with a new one.

If this doesn't resolve the problem then try using a normal flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not damage any internal components, or scratch the plastic. Once the battery is removed then replace it with a new one.

When the new battery is installed, close and unlock the doors using the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to ensure that it's working properly. If the key fob isn't working, contact a dealer or locksmith to resolve the problem. To avoid future lockouts, ensure you purchase an emergency key that will work on all trunk and door cylinders.