The Most Hilarious Complaints We've Heard About Fiat Panda Key Fo…

Reasons Your fiat panda key fob replacement 500 Key Fob Won't Work

A fiat 500 key fob is a great way to open the doors and begin the car. There are many reasons the key fob might stop working. This could be due to a dead battery and water damage, as well as problems with the receiver modules, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to search for local automotive locksmiths). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

The most common reason your 500 key fob won't function is a dead battery. Modern key fobs have only a limited range of operation and must be within just a few inches of the vehicle in order to work. If you're far from your vehicle and hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) by a fresh one of a reliable brand, like Panasonic Duracell or Energizer. You can find them at your local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while you are standing close to your fiat key replacement 500. The parking lights should flash and the key fob will operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it could have water damage that prevents it from communicating with the receiver module inside your car. Water damage can happen in a variety of ways, such as an easy splash or submerging the key fob saltwater at the beach. If you think your fob was exposed to water, place it in a rice bag to draw out the moisture. If this doesn't work, you will need to have your fob reprogrammed either by an auto locksmith or dealer.

Water Damage

Damage to the water supply can occur if you submerge the fob in the ocean or wash it in a washing machine. Saltwater is especially dangerous to the fob's circuit board which causes it to short out and eventually die. Getting the fob wet is not an ideal choice however, if you drop it in a cup of water or forget to remove it from your pants pocket prior to running the washer do not give up hope.

Take the battery off first. Clean the electronic chip using isopropyl ethanol or a similar product and dry it thoroughly before replacing the battery. Next try the fob and check if it functions. If the key isn't working, it may have to be reset. This is typically handled by a dealer or professional auto locksmith.

If your key is old and is not programmed for your car it is necessary to replace it completely. A professional locksmith for cars can complete this simple process. The locksmith will require the key cut to match your vehicle's ignition. They'll also have to program the fob into your vehicle's system. This is a cheap and quick process that could be completed on the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote has a range of 30 feet. Therefore, should you be too far away from your vehicle, it won't respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If you've replaced the coin battery (commonly known as"button" or "button" or "watch") and your fob still won't work, it could have an internal circuit board issue. In most cases, reprogramming the fob will resolve this issue. You can find the procedure for most vehicles on YouTube or in the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in place. If they lose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances it is possible that the fob will become desync'd with your vehicle due to software or hardware issues. This can be a major trouble, but you could usually fix it by visiting an auto locksmith to reprogram your fob. In certain situations it may be necessary to install the software again in your body control module as well.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This could occur if the key fob is located near the radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob might not function include a weak connection to the buttons and internal chip, or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming or using an alternative key fob. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

There is a straightforward method to reset the 500's on-board system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Then, reconnect the battery. This will clear out any remaining electrical charge and restart the car's computers. This can help you the key fob to function again. If the issue continues, you should consult a certified technician. They'll be able determine the root of your problems.