A Step-By-Step Guide To Peugeot Keys From Start To Finish

Peugeot 208 Key Replacement

It is best to delegate the replacement of Peugeot keys 208 to auto locksmiths equipped with the necessary equipment and technical skills. They can program and create keys quicker and more efficiently than dealers.

A dead coin battery is most likely to blame when your key fob stops locking or unlocking the doors. However, there are many other reasons that the key may be malfunctioning.

Dead Coin Battery

A dead coin battery can stop your Peugeot 208 from locking or unlocking, and won't start the engine. If this is the scenario, you'll need make use of the backup starting procedure which is explained in the owner's manual to your vehicle.

Another reason your 208 might not start is that the spark plugs are been damaged. The spark plugs are responsible for igniting the fuel that starts the engine. However, they have a limited life span. They'll eventually fail in the event that they aren't utilized enough.

There is an easy solution to this issue. Verify the voltage of your battery with a multimeter. If it's lower than 11.5 Volts, then you need to replace it. It is also important to clean the battery's contacts if it has corrosion. This can be done by removing the rubber covers from the two terminals of the battery, and then using a wirebrush, you can remove any corroded parts of the battery. Then, you should connect the cables to the positive and negative poles.

Water Damage

If your 208 won't start and the battery is not empty, you must ensure that the spark plugs are in good working order. It could be that they are simply too dirty and they don't spark. The spark plugs can be cleaned in a workshop.

peugeot 207 key replacement cars are equipped with transponder keys that integrates with the car's immobiliser system. This ensures that only a valid key is able to turn the engine. If the chip in the Peugeot key is damaged then it won't send the proper signal to the vehicle.

This is a very common issue that is often caused by water damage. This is particularly common in colder climates where the vehicle may have been exposed to rain or snow. In this case, contact an experienced locksmith who has the required tools and equipment to reprogram the key. They'll also have the latest technology and equipment needed to make the Peugeot smart key. The process should not take more than 15 minutes.

Contacts for the battery that are defective

Peugeot replaced the old transponder chips using a new version that makes use of electronic components that are mounted on a circuit board. This new system works well when it's brand new, however, over time, the circuit boards begin to wear out and stop functioning properly.

This can prevent the immobiliser chip from triggering and causing your car to not start. If this happens, it's recommended to seek out a Peugeot specialist or locksmith.

Another common issue is when the battery in the key fob is dying, this causes the key blade to stop getting into the lock. A locksmith in your car can replace the battery and cut a new blade for you, it's normally a quick fix.

Faulty Receiver Module

If your Peugeot key fob isn't working after dropping it on the ground, being exposed to a sudden rain or accidently washing it or washing it, it could be due a malfunctioning receiver module. The receiver is responsible for sending radio frequency signals to the on-board computer that controls the central locking system of your Peugeot vehicle.

The key fob itself is fitted with rubber seals that block water from reaching the electronic chip inside. However, prolonged exposure to water can cause damage to these seals and the chip. Submerging the key fob into the ocean at the beach or throwing it into the pool can be especially damaging because of the high salt content.

If your Peugeot spare key fob isn't working, you'll need to have the module replaced. This should be done by a Peugeot specialist or a professional auto locksmith. As opposed to other cars, Peugeot keys are protected by an unique immobilizer system that requires the correct programming for the start of the engine. This is why you should go with a knowledgeable Peugeot locksmith for the job of creating and programming an appropriate replacement key for peugeot partner van.

Computers with faulty on-board computers

The on-board computer of your Peugeot is responsible for a variety of features in your car, including airbags and power windows. When something goes wrong in these systems, it will usually show a code that identifies the issue. This code is stored in the system and stays there until the problem has been resolved. Usually, this will mean replacing the computer on board.

One of the most frequent reasons for the light coming on is loose or corroded connection in the airbag sensor. This could be due to wear and tear, aging, or exposure to salt and moisture. It is important to have this issue resolved as soon as possible, as an airbag that is malfunctioning can be risky in the event of an accident.

If your Peugeot is showing a card that is not being detected error, then the key battery in the key fob could be dead or weak. This will stop the key fob from sending a signal to disable the immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob and then trying to start your vehicle. If this does not work then the battery in the key is in need of replacement.