Why Peugeot Keys Will Be Your Next Big Obsession

Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to experienced auto locksmiths with the right equipment and know-how. They can create and program new keys quicker than a dealership and at a lower cost.

A dead coin battery is the most likely cause the reason your key-fob stops locking or unlocking doors. There are other causes that the key could be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as making it impossible to start the engine. If this is the situation, you'll need utilize the backup starting method which is explained in your vehicle's owner manual.

The spark plugs could also be worn out. The spark plugs ignite fuel to start the engine. They only last for a certain amount of time. They'll eventually degrade if they're not used enough.

Luckily, there is an easy solution to this issue. The best option is to test the voltage of your car battery with a multimeter. If it's less than 11.5 Volts, then you need to replace it. It is also important to clean the contacts of the battery when it has corrosion. You can do this by lifting the rubber covers that cover both battery terminals and using a wire brush to remove any corroded areas of the battery. Then, you should connect the cables that connect the positive and negative poles.

Water Damage

If your 208 isn't starting and the battery isn't running, then make sure that the spark plugs are working. You might find that they are simply too dirty and don't spark. This can be fixed easily by cleaning the spark plugs in an workshop.

Peugeot cars use a key with a transponder that is compatible with the immobiliser. This ensures that only the right key can start the engine. If the chip inside the Peugeot key is damaged, then it will not send the correct signal to the vehicle.

This is a typical issue that is caused by water damage. This is a common issue in colder climates where the vehicle has been exposed to rain or snow. If this is the case, get in touch with a reputable locksmith who will have all of the tools and equipment needed to reprogram the new key. They'll also have the latest technology and equipment needed to create the Peugeot smart key. The process should not take more than 15 minutes.

Faulty Battery Contacts

Peugeot replaced the transponder chips with a brand new type that uses electronic components mounted on a circuit board. The new system works great when it's brand new, but the circuit boards deteriorate over time and stop working properly.

This could stop the immobiliser chip activating and causing your car to not start. If this is the case it's a good idea seek out a peugeot 3008 key fob specialist or locksmith.

A common problem is when the battery in the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A locksmith in your car will replace the battery and then cut a new key blade for you. This is a quick fix.

Faulty Receiver Module

If your Peugeot key fob isn't working after dropping it on the floor, or being exposed to a sudden rain or accidently washing it the wrong way, it could be due to a defective receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which controls the central locking system of your Peugeot vehicle.

Rubber seals on the key fob block water from reaching its electronic chip. However prolonged exposure to water may penetrate these seals and damage the chip. Submerging the key fob into sea water at the beach or throwing it into the pool can be especially damaging because of the high salt content.

The module will have to be replaced if your Peugeot spare key does not work anymore. This is only done by an expert auto locksmith or Peugeot specialist. In contrast to other vehicles, Peugeot keys are protected by an immobilizer that is unique and requires the correct programming for the start of the engine. This is why you must choose a reputable Peugeot locksmith to handle the task of creating and programming an appropriate replacement.

Computer on-board is not working properly

The on-board computer of your Peugeot is responsible for many of the features in your car, including power windows and airbags. The on-board computer displays a code if something goes wrong. This code is stored in the system and stays there until the issue is resolved. This will often require the on-board computers to be replaced.

The most frequent cause for the warning light of the airbag to illuminate is corrosion or loose connections within the sensor. This could be due to wear and tear, aging or exposure to salt and moisture. It is important to have this issue addressed as quickly as possible, since an airbag that is malfunctioning can be dangerous in the event of an accident.

If you notice a card not found error on your Peugeot, the key battery inside the key fob might be dead or weak. This can prevent the key fob from sending a signal to disable your vehicle's standard immobilizer. Try this by pressing the unlock button on the key fob, and then trying to start your car. If this does not work then the battery in the key fob has to be replaced.