The Reasons Kia Picanto Key Fob Replacement Has Become Everyone's…

How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with a keyless entry system built in. This key usually resembles the remote control and can be exchanged with a new one from an Kia dealer or locksmith.

Key fobs can stop working due to a variety of reasons, such as the battery being dead, worn-out buttons, signal interference or water damage. Here are some tips on how you can get your Kia Sportage replacement key to work again.

How do you replace a remote key or a smartkey?

No matter if your kia replacement key fob (here.) is equipped with an intelligent key, remote key, push-to-start keys, or a standard non-transponder key made of metal, the battery in these keys will eventually need replacement. This is especially true if your car displays a message telling you that the remote or smart keys have low battery power.

Luckily, it's an easy process. In order to replace the key fob battery remove the mechanical key from the slit on the back of the key fob. Next, lift the cover. Inside the key fob will be tiny screws that hold the battery in the correct position. Remove the old battery by unwinding the screw with a small screwdriver. Then, insert the new and close the slit inside the key fob.

Test the key fob by pressing the lock and unlock buttons. You're good to go If the doors lock and unlock as you expect. You can now use your Kia's hands-free lock/unlock feature when your fingers are cold or you have to make errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming done. This requires a programming machine that is only available to the locksmith in the automotive or dealer. Other keys (non-transponder metal keys) don't require programming. If your key needs to be programmed again, you must know the key code number stamped on the tag that identifies the key and save the number in a secure place.

How do I replace a battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, it is a sign that the battery should be replaced. A weak battery could cause other issues, such as the check engine light flashing or the engine not working correctly. Fortunately replacing the key fob battery is a fairly simple DIY project that requires only the most basic tools.

Make sure that you shut off your vehicle and shut the doors before you begin. Find the small metal or a plastic piece at the bottom of the key fob. Press it until the metal key is released. Then, you can put the key into the driver's door handle to unlock your car.

To replace the battery on the key fob, take off the cover on the rear. Utilize a plastic plier tool to loosen the latch that holds the black negative cable. Remove the old battery, and then align the new one to ensure that the "+" positive side faces your face and the "negative" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid damaging or bending the contacts of the metal.

Once the new battery has been installed, turn the key fob off and on in the ignition for a few times until the door locks. Then you can test your Kia key fob to see whether it's working again.

How do you replace a smart keys

You may have either an ordinary keyfob or Smart Key depending on the model of Kia Sportage. The difference between the two is that the smart key has a small mechanical key blade hidden within it, whereas the standard key fob does not. Both key fobs are equipped with batteries that will eventually require changing. This is a simple procedure that takes just two minutes.

Before you start before you begin, make sure that you are on a level surface with sufficient lighting and that your Kia is off. Also, remember that there are tiny parts inside the fob that can be snagged if not careful.

The release button for the small size is located on the lower backside. It's either a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened, you can simply take out the old battery and replace it. The new battery is C2032, and can be bought from a local or online auto parts store. After you're done, your key fob should be able to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How do I replace the mechanical key

The Kia keyfob can be a fantastic convenience which allows us to lock or unlock our car simply by pressing one button. Like any device that is used, the kia picanto key fob replacement key fob might have issues. There are solutions to resolve these issues and keep your key fobs functioning for many years.

One of the most common issues is a low or dead battery. This can cause the fob to cease working or stop working at times. If this is the problem then replace the battery with a new one.

If this doesn't fix the problem then try using a normal flat-head screwdriver to break open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery that was removed and replace it with a brand new one.

After the new battery has been put in, close and then open the doors with the mechanical key (every kia fob has an emergency mechanical key that will fit into the slot). Test the key fob to ensure it's functioning correctly. Contact a dealer or a locksmith to resolve the problem in the event that the fob is not working. To avoid lockouts in the future, ensure that you have an emergency key that will be able to work with all trunk and door cylinders.