11 Ways To Totally Defy Your Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are easy to maintain and durable, as well as long-lasting. In contrast to aluminium and timber, they do not rust or rot.

It is important to clean and oil UPVC windows and doors on a regular basis. This will help prevent unnecessary repair costs and also increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and may even be fatal. It is crucial to take the time to ensure that you're doing all you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace and will usually fit into the old frames very easily. If windows with double panes are held together by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this case, it is necessary to buy plastic spacers to make sure that the new pane fits into the window frame.

If you're planning to try to remove the window panes yourself it is important to wear the proper safety gear, including thick gloves and protective eyewear. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards of glass fall onto the fabric, not onto the floor and could be trampled.

It's a good idea to seal the gap after the glass is removed. This will prevent water and drafts from entering your property until a professional comes out to fix the window. It also acts as an obstacle to stop intruders from getting into your home. If the gap is particularly large, you might want to consider using the security door with an integrated window, as it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are a low-cost, durable and energy-efficient alternative to timber windows with sash. As time passes, they may develop a number of problems that include sliding. A window that isn't properly aligned can cause problems with light, draughts and even security. It's important to take action when you discover that your uPVC windows are sliding.

To fix a window that is sagging you can try to reposition the hinges. You'll first need to open the windows to get at the frame. With the screwdriver, you'll be able to remove the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, close the window and verify the an appropriate fit. If you're happy with the fit, you can tighten the screws to ensure that they remain in the right place.

If you aren't able to move the hinges, you might require replacing the seal. Rubber seals can dry out and lose their elasticity with time, which causes them to lose their tightness. It is important to replace your seal as quickly as you can in order to keep your uPVC window watertight and draughtproof.

UPVC handles can also become loose. Most often, this is caused by screws that have become loose over time. However, it could be due to the fact that the handle mechanism has been worn out. It's a good thing that it's simple to fix the handle of a window that is loose yourself. The first step is to close the window and perform an experiment fit. The joint at the corner of the sash must align with the joint on the casing. If it isn't then you can make use of a screwdriver to loosen the handle, and then turn the mechanism back into the position it was in.

3. Water Leaks

If you're waking up to damp floors and mouldy walls each time it rains it is important that you take action. Water leaks from windows not only lead to the degradation of your home's structure but also undermine your efforts to regulate the temperature within your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or missing.

This is a fairly simple fix that can be done by any competent DIYer. Depending on the severity of the issue the caulking that was used up might need to be removed before a new layer of caulk can be put on. It is important to keep in mind that when it comes to uPVC window repairs, you should avoid the temptation to "over-caulk in order to make the area more difficult to clean and reduce your energy efficiency.

Check that any drainage holes do not have debris inside them and ensure that the sill pan has been properly angled to drain away from the window. In more serious cases you may need to think about replacing the window.

Mold spots and rotted sills are also signs of water leakage. The fungus thrives in damp conditions and is able to quickly spread throughout the house.

It is also important to note that if the leak is coming from between the glass of your double glazing repair-glazed windows, it's more likely to be an issue with the glass seal rather than the frame or sliding. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame when your uPVC window is difficult to open, or if it opens in an ease. Anyone with the skills to fix them can replace the hinges in a matter of minutes.

Like all mechanical parts hinges will be damaged over time. It is an easy procedure, but it is simpler if you have someone to help hold the frame up.

Make sure that the uPVC hinges open and close in the proper direction. This can be done by checking for the arrows on each hinge, this shows which way the window should open.

Window hinges that aren't working properly can be caused by incorrectly opening the window a certain manner or because of poor installation at the factory. This can often be resolved by sending us a photograph via our website and we will be pleased to offer you suggestions.

It is also important to ensure that the hinges are lubricated regularly. This can be done by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window operate and close more easily. It can also stop corrosion and decrease the chance of sticking. Ideally, you should do this once a year. WD40 and other solvent-based lubricants are not recommended as they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different factors. Firstly the hinges, again because of wear and tear, may become displaced, which causes a gap to form where the sash meets the frame. They can be fixed by giving them a good clean, but in the event that they are beyond repair it might be necessary to get them realigned or replaced. Second, the interlock can be disaligned. It is located on the hinge side and could require to be cleaned. In certain instances it might be necessary to replace the hinges.

The next common cause of draughts is the window seals, these are susceptible to being worn out or damaged over time, and will allow air to escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help control indoor temperatures, and reduce draughts.

One of the most effective methods to reduce draughts is by using a draught excluder. These are usually fabric tubes that are filled with some type of filler. They can be placed on top of your windowsill. They can help stop cold air from entering and keep your home warm and cozy!

With a little regular maintenance and repairs windows made of upvc will continue to provide a great level of insulation and security for your home. However, it is important to recognise that all windows have a lifespan and eventually, they will reach a point where it is more cost-effective to replace them rather than repair them. If you are experiencing issues with your upvc window it is recommended to speak with an expert as soon as possible.