The Worst Advice We've Been Given About Fiat Panda Key Fob Replac…

Reasons Your fiat panda key fob replacement 500 Key Fob Won't Work

A Fiat 500 key fob makes it easy to open doors and start your vehicle. There are many reasons the fob could stop working. It could be due to a dead battery damaged receiver module, water damage issues, and interference.

This listing is for an NEW replacement fiat 500 key replacement cost Flip Key Remote - similar to the Ilco brand that must be programmed professionally by a local locksmith (click here to search for a Locksmith Search). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

The most common reason your 500 key fob will not function is the battery is dead. Modern key fobs have a very limited range of operation, and must be within a few feet of the vehicle to operate. If you're far from your vehicle when you press the key fob button the car won't respond and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin cell battery (Part number CR2032) with a fresh one from a reputable brand such as Panasonic, Duracell, or Energizer. They are typically available in your local hardware store or on the internet.

After you've replaced the coin cell battery You can test it by standing in front of your Fiat 500 and pressing the buttons. The car will blink its parking lights and the key fob should be able to operate the lock and unlock switches.

If the fob's key doesn't work after replacing the battery, it could have water damage that stops it from connecting to the receiver module inside your vehicle. Water damage can happen in many ways, including simply splashing or submerging your key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, you can place it in a bag of rice to draw out the moisture. If that doesn't work, the fob might require reprogramming by an experienced auto locksmith or by the dealer.

Water Damage

While the fob comes with rubber seals that keep water out of the chip's electronic circuit it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the fob's circuit board which causes it to short out and eventually die. The fob getting wet is not a good idea but if you accidentally drop it in a glass of water or fail to remove it from your pants pocket prior to running the washer do not give up hope.

Take the battery off first. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Test the fob next to verify if it's working. If the key isn't working it could need to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key is newer and hasn't been programmed to your vehicle, it will likely need to be replaced completely. This is a simple procedure that can be handled by a professional automotive locksmith. The locksmith will require the key cut to match the car's ignition. The locksmith will also have to reprogram your fob in the car's system. This is a low-cost and quick procedure that can be completed on the same day.

Receiver Module Issues

Your 500 key fob might not function because it's out of range. The remote typically has 30 feet of range or less, and if it's too far from your car, it will not respond to your commands. You can easily solve this issue by moving the remote closer to your car until it responds.

If you've replaced the coin battery (commonly known as"button" or "button" or "watch") and your fob still won't work, it could have an internal circuit board issue. Reprogramming the fob is usually the solution to the issue. The instructions are available for the majority of vehicles on YouTube or in the owner's manual.

It's possible that you need to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension it can prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare instances, the fob could be out of alignment with your vehicle because due to hardware or software issues. This could be a huge headache, but you can usually fix it by visiting an auto locksmith to reprogram your fob. In some cases, the software may also require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This may happen if the keyfob is located in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob may not work due to a bad connection with the buttons or water damage, or damage to the internal chips.

If the key fob stopped working one day out of the blue, or after trying everything you can do at home to solve it e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a defective receiver module on your 500. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It transforms the signals into electronic commands which are then translated by the vehicle.

There's a simple method to reset the 500's on-board system including the keyfob. Disconnect the battery 12 volt for about 15 minutes, by disconnecting the negative cable first then the positive cable. Then reconnect the battery. This will eliminate any remaining electrical charge, and then restart the computer in your car. This will help you get your key fob working again. If the issue persists you should speak with an experienced technician. They can determine the exact cause of your problems.