Peugeot Keys Tips From The Best In The Business

Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to professional auto locksmiths who have the proper equipment and technical know-how. They can make and program new keys faster than a dealership would and at a lesser cost.

If the key fob stopped locking or unlocking your doors, it is likely due to a dead coin battery. But, there are other reasons why the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will hinder your Peugeot 208 from locking or unlocking and will not start the engine. If this is the scenario, you'll need use the backup starting method that is detailed in the owner's manual for your vehicle.

The spark plugs could also be worn out. Spark plugs are what ignite the fuel to start the engine. However they have a short life span. If they're not used enough, they will eventually fail.

There is a simple solution for this problem. The best option is to check the voltage of your car battery with a multimeter. If it is below 11.5 volts it is time to replace it. It is also essential to clean the battery's contacts in the event that it is damaged by corrosion. This can be done by lifting the rubber covers covering the two terminals of the battery and using a wire brush to remove any corroded parts of the battery. Then, you should connect your cables to connect the positive and negative poles.

Water Damage

If your 208 won't start and the battery hasn't gone flat, you should look at the spark plugs. It could be that they're overly dirty, causing them to not to spark. This can be easily corrected by cleaning the spark plugs in an workshop.

Peugeot cars use a key with a transponder that is compatible with the immobiliser. This ensures only the correct key is able to turn the engine. If the chip in the Peugeot key is damaged then it won't send the proper signal to the vehicle.

Water damage is a typical reason for this issue. This is a typical issue in colder climates where the vehicle has been exposed to rain or snow. In this situation, contact a reputable locksmith who has the tools and equipment needed to change the key's programming. They will also have all the latest technology and equipment needed to create the Peugeot smart key. The process shouldn't take more than 15 minutes.

Contacts for the battery that are defective

Peugeot replaced the transponder chips with a brand new model that utilizes electronic components mounted on a circuit board. This new technology works great when it's new, programmers but over time the circuit boards start to lose their effectiveness and cease working properly.

This can prevent the immobiliser chip activating the immobiliser chip, causing your car not to start. If this happens, it's best to call a Peugeot specialist or locksmith.

A common issue is when the battery in the key fob begins to fail. This causes the blade of the key to stop feeding into your lock. A locksmith in your car will replace the battery and then cut a new blade for you. This is a quick fix.

Faulty Receiver Module

If your Peugeot key fob stopped working after dropping it on the ground, being exposed to a sudden downpour or accidently washing it may be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequency to the onboard computer that manages the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from getting to the chip inside. However prolonged exposure to water could be able to penetrate these seals and cause damage to the chip. Submerging the key fob into sea water at the beach or throwing it into the pool can be especially damaging because of the high salt content.

If your Peugeot spare key fob doesn't work it is necessary to have the module replaced. This is only done by an Peugeot specialist or an expert auto locksmith. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the right coding to start the car. This is the reason why you should only trust an experienced Peugeot locksmith with the task of creating and programming a replacement.

Computer on board is not working properly

The on-board computer in your Peugeot is responsible for a variety of functions in your car including power windows and airbags. When something goes wrong with these systems, it'll typically display a code indicating the problem. This code is stored in the system and will remain there until the issue is fixed. This can often mean that the on-board computers to be replaced.

One of the most frequent causes of the light turning on is the loose or corroded connectors in the airbag sensor. This can be caused by wear and tear, aging, or exposure to moisture and salt. This issue should be addressed as soon you can, since an airbag that's malfunctioning could pose a risk in the event of an accident.

If your Peugeot is showing a card not detected error, the battery in the key fob might be dead or weak. This will stop the key fob sending a signal to deactivate your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then trying to start your vehicle. If it doesn't work it is because the battery of the key is in need of replacement.