10 Tell-Tale Signals You Need To Buy A Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A key fob with the fiat 500 replacement fiat 500 key fob Key fob [highwave.kr] 500 number is a handy way to unlock the doors and start the car. There are a variety of reasons why the fob could stop working. This includes a dead coin-battery water damage, receiver modules issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to find local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not working. Modern key fobs have a limited range of operation, and must be within some feet of the vehicle to function. If you are far from your vehicle, and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) by a new one from a reputable manufacturer like Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store, or online.

You can test the battery of your coin-cell by pressing the buttons while you're standing close to your Fiat 500. The car should flash its parking lights and the key fob should operate the lock and unlock switches.

If your key fob still doesn't work even after replacing the battery, there may be water damage which hinders it from communicating with the module in your vehicle. Water damage can happen in a variety of ways, from a light splash to submerging the fob in salt water at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to draw the moisture back out. If this fails, you'll require your fob to be changed by an auto locksmith or a dealer.

Water Damage

The fob does have rubber seals that keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater is particularly dangerous to the fob's circuit board and can cause it to short out and eventually end up dying. The fob getting wet is not an option but if you accidentally drop it into the water in a cup or do not remember to take it out of your pocket before you run the washing machine do not give up hope.

Remove the battery first. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Then check the fob to see if it works. If the key isn't working then it might need to be reset. This is usually handled by an auto locksmith or dealer.

If your key is older and is not programmed to work with your vehicle, you will need to replace it completely. This is a simple process that can be carried out by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition in your vehicle. The locksmith also needs to reprogram your fob in the car's system. This is a cost-effective and quick process that can be completed within the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote's range is of 30 feet. So when you're too far away from your vehicle it won't be able to respond to your commands. You can easily solve this problem by moving the remote closer to your car until it responds.

If your fob does not work after replacing the battery inside the coin, which is also called a "button", "watch" or "button" it could be due to a problem with the circuit board inside. In most cases, reprogramming the fob will fix the problem. You can find directions on how to do this for most vehicles by searching YouTube or checking out the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in place. If they loose tension it can prevent the coin battery from being properly seated, and this will cause your remote to malfunction.

In rare instances it is possible that the fob will become disconnected from your vehicle due to software problems or hardware issues. This could be a huge headache, but you can frequently fix this issue by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain instances it may be necessary to install the software again in your body control module, too.

Interference

In addition to a dead battery on a coin, the key fob may not be able to receive or transmit a signal due to interference. This could happen when the keyfob is located in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons why the key fob could not function include a weak connection to the buttons, damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. replacing the battery, reprogramming, and using the spare key fob, you could have a malfunctioning receiver module on your 500. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands, which are then translated by the vehicle.

There's a simple method to reset the 500's onboard system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Reconnect the battery. This will clear out any remaining electrical charge and restart the car's computers, which could help get your key fob working again. If the issue continues, you should consult an expert technician. They will be able to identify the exact cause of issues.