Indisputable Proof That You Need Double Glazing Door Lock Repairs

Double Glazing Door Lock Repairs

Has your uPVC window or door mechanism deteriorated? Perhaps the door or window handles aren't able to connect properly or are hard to use.

It is essential that the double glazed doors operate smoothly, otherwise you will lose energy and increase the chances of burglary. Owen the Locksmith will be able to repair your door lock at a reasonable cost.

Snapped Key

It can be quite frustrating when a key is snapped into a lock. It's also potentially an issue for security, since the door may not lock and make you open to intrusion. Fortunately, there are some simple fixes you can try to resolve the issue and get your door operating properly again.

Remember to remain calm. If you panic you may end up pushing the damaged key piece further into the lock.

Next spray WD-40 or another penetrating oil into the lock to aid in making the broken piece to slide out more easily. You can also use the screwdriver to break off any pieces that are stuck. If you happen to have a small piece of the key hanging out it, you can use a paperclip or some other metal object with a thin surface to grab it and pull it out. Both methods work, but you must be careful not to push the broken key piece further into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades also work well for this. If you don't have any of them handy, you can make use of needle-nose pliers to bend them and create hooks. You can also use a pair of tweezers grab and remove the last bit of the broken keys.

If you can't get the broken piece of key out, you can try using a lock de-icer. It's usually available at all hardware stores. It is used to freeze any moisture or ice that might be in the lock.

If none of these solutions seem to work, it may be time to contact a locksmith. The experts at Fitlocks can quickly solve problems like broken handles or snapped keys using uPVC locks and door mechanisms. They can also alter your double glazing door mechanisms to make them easier to operate. Request a repair for your double glazing with us online, or give us a phone call to discuss your needs.

Broken Cylinder

A broken cylinder can pose a serious security risk. It's fortunately a simple repair for professional locksmiths to complete. To fix the cylinder locksmiths will need to tap it. They can do this using an hammer or another tool, but the most efficient way is to use a long match or a piece of wire. Then, position the end of the match or wire near the keyway. The locksmith will then strike the lock to crack it. This is superior to using a hammer, which can cause damage to the lock.

Overheating is the primary cause of cylinder heads cracking. This can happen when the cylinder block and head are made from different metals, such as cast iron and aluminium. Different metals can be heated and cool at different rates. This can cause localized hotspots to expand faster than the rest of the cylinder.

Corrosion is another possible reason for cracks in the cylinder. When the cylinder head and the block of the cylinder are not properly maintained, it can cause corrosion or rust that could cause them to expand at more than they should. This can cause cracks as time passes.

If your uPVC window or door lock is rigid and requires more pressure to turn it could be due to a variety of causes. This issue could result from a defective locking mechanism, or misalignment or a worn-out handle.

Fortunately it is a simple and affordable fix for the majority of homeowners with double glazing. A professional locksmith can usually fix this problem within one hour of arriving at the home. Depending on your needs they will be able to replace the locking mechanism, replace the window handles, or change the gearboxes. A professional locksmith can always advise you on the most cost-effective options for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders that give you an extra security layer from burglars. It's a small price to pay for the security that comes from knowing that your uPVC doors are safe.

Broken Handle

It's not surprising that window handle locks can break. They have complex mechanisms that become less effective over time. If yours breaks it's difficult to determine the source of the issue and make sure you fix it correctly.

Repairing your damaged handle, whether it's an internal latch or locking mechanism can increase the security of your uPVC door and stop draughts. It is costly to replace or repair your handle if it is not done correctly and can also damage the frame and the lock of your door.

With the window in the open position then loosen the screw that holds the handle with a screwdriver. The screw should be located on the inside of the backplate, which is usually covered by the cap of the screw for aesthetic reasons. Be sure not to lose any internal parts within the handle, like the plates or levers that are on the opposite side of the spindle. It is best to keep them in the same order so you can re-install them if needed.

Then, using a second screwdriver take the screw off that connects the handle to the spindle in the back. Once this is removed, you should be capable of pulling the handle away and pull off the damaged spindle. Replace it with a brand new spindle, ensuring that it's the same length (you can purchase them online or in hardware stores). Screw it in place. Don't over tighten the screw as this can harm the handle as well as the window frame.

Ensure the new handle is correctly fitted, then close and test the handle. Hopefully, it will work smoothly and you'll be able unlock your window.

While you're working on the handle, make sure to check your uPVC windows are shut correctly. If they aren't closing properly, you could experience damp or draughts inside your home. You could also compromise the energy efficiency of your home. A local window company, such as Core Sash Windows, will be capable of adjusting the hinges on your window repairs near me frames to ensure they are able to shut properly.

Broken Spindle

It is more likely for the spindle to break rather than the handle. This is especially frequent in upvc door repairs near me tilt and turn windows. These windows require a handle that acts as an locking device within the frame of the window. The handle is attached to a centre rod that in turn activates cams that resemble mushrooms, which secure the frame of the window. If the dead latch mechanism fails to open after the handle has been turned, it's likely the spindle has been damaged. This could be a frustrating issue.

There are ways to fix this issue. A reputable locksmith will be able to quickly and effectively fix this problem. A professional locksmith will be able disassemble the window's handle using a tool to take out the wheel portion in which the spindle is. This is done without damage to the handle or the window frame.

Once the wheel has been removed, the technician will inspect the spindle to determine what caused it to break. This involves breaking the spindle into its constituent components and carefully observing their general condition as in addition to any specific areas of damage or excessive wear. This process is usually carried out by technicians working in a clean and safe environment.

The next step is to clean the damaged spindle. This will help remove any debris or dirt that could be hindering it from functioning normally. After this the spindle is cleaned, it could be repaired or replaced. If it is being replaced the technician can take an identical dowel size to the original and drill mating holes into both parts of the spindle. This will ensure that the spindle is perfectly matched with the handle.

If the spindle that is damaged is beyond repair, it could be necessary to replace it entirely. Home centers sell generic replacements. However, if the style of your window is rare then it is necessary to find a woodworker or cabinet maker who can make the exact model for you. After the spindle is installed, it can be fixed to the handle. Place the screw holes on the handle with the screws that are already in the frame. Once the new handle is in place, you'll be able to operate your uPVC window.