How A Weekly Kia Picanto Key Fob Replacement Project Can Change Your L…

How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with the keyless entry feature built in. The key is usually akin to an electronic remote and can be exchanged with a brand new one from an Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, such as the battery being dead, worn-out buttons signals, signal interference or water damage. Here are some suggestions to help you get your Kia sportage replacement key working for good.

How to replace a smartkey or remote key?

The battery inside your Kia's smart key will eventually need be replaced, whether it's a remote as well as a push-to start key or a regular key that does not contain transponder. This is especially relevant if your vehicle displays a message telling you that the remote or smart keys have low battery power.

This is a relatively easy process. To replace the battery in the keyfob take out your mechanical key from the slit at the back of the fob. Then, you need to pry the cover off. A small screw is in the key fob to keep the battery in the correct position. Using a small screwdriver, remove the screw and remove the battery that was in place. Then, you can insert the new battery and close the hole in the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're good to go! You can now utilize the hands-free lock/unlock feature on your Kia whenever your fingers feel cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a programing machine that is only available to the locksmith for cars or dealer. Other keys (non transponder metal keys) do not require programming. If you need to reprogramme your key, you'll need to note the key code's number on the tag for the key code.

How do you replace the battery?

If the kia car key replacement key fob is unable to respond to pressing the lock or unlock button, it is most likely that the battery is low. A battery that is not functioning properly can cause other issues, like the check engine light turning on or the engine not cranking properly. It is easy to replace the key fob battery with just a few simple tools.

Be sure to turn off your vehicle and close all doors before you begin. Find the small metal or plastic piece on the bottom of your key fob, and jiggle it until a metal key slides out. Then, you can insert the key in the door handle of the driver to open your car.

To replace the battery in the key fob, remove the rear cover. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and align the new battery to ensure that the "+" positive side faces you and the "negative" negative side is facing the fob's metallic electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or breaking the metal contacts.

After you have installed the new battery and turning the key fob on and off in the ignition until the door locks cycle. Then you can test your kia key replacement key fob to determine whether it's working again.

How do I replace a smart key

Depending on the model of your Kia Sportage, you may have the standard key fob, or a smart key. The difference between the two is that the smart fob has a small mechanical key blade in it, whereas the standard key fob does not. Both types of key fobs are equipped with batteries that eventually will need to be replaced. Luckily, this is an easy task that will take about two minutes.

Be sure to switch off your Kia Ceed Key fob replacement and stand on a level or well-lit surface prior to when you begin. Also, keep in mind that there are tiny pieces inside the fob that can be removed if not cautious.

The first step is to find the small release button that is located on the back of the lower part of the fob. It can be an oval silver button or a rectangular slot. When you press it, the mechanical key blade will pop out and you can then open the key fob.

Once the key fob is removed, you can remove the old battery. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. After installation you should be able to lock, unlock and start your car with your key fob even if the engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob is a great convenience that lets us lock or unlock our car by simply pressing a button. But like any device it may have issues from time to time. There are steps to take to fix these issues and ensure that our key fobs are in good working order in the long run.

A dead or weak battery is among the most common problems. The battery could cause the device to stop working or work intermittently. If this is the problem it is time to replace the battery an entirely new battery.

If this doesn't fix the issue, try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to scratch any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's functioning properly. If the fob still isn't functioning, contact an authorized locksmith or dealer to resolve the issue. To avoid future lockouts, make sure you get an emergency key that can work on all trunk and door cylinders.